3M Splice 中間接頭

Product>>Splice>>3M Splice 冷縮預撐電纜中間接頭

^{The 3M
product line covers splicing needs from 0-600V to 35 kV applications.}

^{Cold
Shrink Splices}

^{3M cold
shrink splicing products are supplied pre-stretched on a removable core for
efficiency and ease of installation. The removable core unwinds after
positioning the splice, allowing the product to shrink into position and
form a moisture resistant seal. All 3M cold shrink products require no
special tools, flame or training to install.}

^{Molded
Rubber Splices}

^{3M molded
rubber QS and QS-II kits are molded from specially formulated, peroxide
cured, EPDM rubber to provide a reliable medium voltage inline splice with a
life expectancy equal to the cable.}

^{PILC
Splices}

^{3M cold
shrink splice kits for Paper Insulated Lead Covered (PILC) cable use 3M
patented oil stop technology. Kits install without soldering or lead wiping.
3M cold shrink PILC splices allow quick installation time without the need
of open flame or heat. Single conductor splice kits rated 1000V and 15 kV
allow inline splicing of PILC to PILC or PILC to Poly/EPR insulated cable.
Three conductor cable splice kits rated 15 kV are designed to transition
splice three conductor PILC to three single conductor poly/EPR insulated
cables. All splices are jacketed and can be fully submersed. Modular splice
kits are available for single conductor PILC equipment connections and tap
splicing.}

^{Resin
Splices}

^{3M resin
splicing kits are used in a variety of applications where conditions require
the unique properties of 3M resins. The splicing kits have a high degree of
mechanical strength for physical protection of connections and provide
moisture-resistant insulation in above ground or direct burial applications.}

^{Tape
Splices}

^{When you
want the versatility of tape, Scotch cable splicing kits are the answer for
almost any application, regardless of cable type or size. Scotch splicing
tape is designed for extra-long shelf life, so there’s less chance of being
caught without the supplies you need for emergencies. Tape products are
available to splice cables from 600V to 69 kV.}

^{Please
tell us what application your is.}

^{What is
Voltage?（1 kV__ 5 kV__ 8 kV__ 15 kV__ 25/28 kV__ 35 kV）}

^{What is
Insulation Level? (100%__ 133%）}

^{What is
Conductor Size? (AWG/kcmil）}

^{What type
of Shielding? (tape, drain wire, UniShieldR, LC Shielded, Jacketed
Concentric Neutral)}

^{What is
Conductor Material? Copper/ Aluminum}

3M 中間接頭 25KV QSG Cold Shrink Splice

	最大被覆外徑 (mm)	絕緣外徑 (mm)	導體線徑 (mm2)	最長套管長度 (mm)	套管外徑 (mm)
QSG 150 AP-1	43	18.8~30.0	25~150	170	14.0~30.0
QSG 300 AP-1	51	21.2~34.5	90~300	170	18.0~34.5

3M QS-III Splice 冷縮預撐電纜中間接頭

^{Item # 型號}	⁵⁵¹⁵	⁵⁵¹⁶	⁵⁵²⁵	⁵⁵²⁶	⁵⁴⁵⁷
^{KV 電壓}	¹⁵	¹⁵	^25/28	^25/28	^25/28
^{Cable 電纜}	^{Shielded Cable 適用銅帶/線遮蔽電纜}				^{(Jacketed) Conecntric Neutral cables. (被覆化)共用中心線}
^{Conductor Size} ^{導體截面(mm2)}	^185-325	^400-725	^185-325	^400-725	^185-325
^{Cable Insulation O.D.} ^{絕緣外徑(mm)}	^25.9-39.4	^32.8-50.8	^28.2-41.6	^36.2-53.3	^28.2-41.6

^{3M QS-II Splice
Kits 預鑄橡膠中間接頭}^{- 3M Molded Rubber Splices}^{5400 Series}

The 3M molded rubber QS and QS-II and QS-UU kits are molded from specially formulated, peroxide cured, EPDM rubber to provide a reliable medium voltage inline splice with a life expectancy equal to the cable.

Type	Item No.	Cable Insulation Dia. 絕緣層外徑(mm)	Conductor Size (mm2) 導體線徑				Notes
Type	Item No.	Cable Insulation Dia. 絕緣層外徑(mm)	5KV	8KV	15KV	25KV	Notes
Splice 中間接頭	5411	16-23	60-100	50-100	35-60
	5412	21-27	125-200	125-180	80-125
	5451	21-26				35-50
	5421	23-27				60-80
	5422	27-31	250	200-250	150-200	95-100
	5423	28-34	325	325	250	125-180
	5424	34-39	400-500	400-500	325-400	200-250

^{0~600 V
低壓中間接頭/1KV~5/8KV中間接頭/15KV 25KV 28KV 35
KV中間接頭(預張式絕緣套管/灌膠式接頭/預張式直路接頭/冷縮式)(單蕊/3蕊)(無遮蔽電纜/遮蔽電纜)(鎧裝/非鎧裝) (pdf 1.5 MB
其他請參考以上連接
中文型錄)}

^{3M Splices Selection Guide
(pdf 970KB English pdf info)}

^{Please check
the pdf file above, you will see the following products. 其他請參考以上連接}

^{Low Voltage Splices 0-600V}^{(1000V
rated)}

^{Cold Shrink
Splices (0-1000V)}

^{3M Resin
Splices 0-600V (1000V rated)}

^Resin

^{5/8 kV, 15 kV
and 25 kV Resin Pressure System}

^{Heat Shrink
Splices 0-600V}

^{1 kV to 5/8 kV Splices}

^{1/C, 1-5 kV,
Non-Shielded Resin Splices}

^{1/C, 5/8 kV,
Non-Shielded Resin Splices}

^{1/C, 5/8 kV,
Shielded-Tape, Wire, and UniShield Cold Shrink Splices}

^{5 kV In-line
Splice Kits, 1/C or Multiple Conductor Unshielded Cable}

^{3/C, 600V and
1 kV, Non-Shielded Cold Shrink Splices}

^{1/C, 3/C, 5/8
kV, Non-Shielded Armored or Non-Armored Armorcast/Cold Shrink Splices}

^{1/C, 3/C, 5/8
kV, Shielded Armored or Non-Armored Armorcast/Cold Shrink Splices}

^{1/C & 3C ,
15/25/28 kV Shielded Armored & Non-Armored Armorcast/Cold Shrink Splices}

^{1/C, 15/25/28
kV, JCN/CN, Tape Shield, Wire Shield, LC Shield Cold Shrink Repair Splices}

^{3/C, 5 kV,
Non-Shielded Armored or Non-Armored Resin/Cold Shrink Splices}

^{3/C, 5/8 kV,
Shielded Armored or Non-Armored Resin/Cold Shrink Splices}

^{15 kV Splices}

^{1/C JCN/CN
Molded Rubber Splices}

^{1/C, 15 kV,
JCN/CN Molded Rubber Splices}

^{1/C, 15 kV,
JCN/CN Cold Shrink Splices}

^{1/C, 15 kV,
Shielded-Tape, Wire, UniShield Molded Rubber Splices}

^{1/C, 15 kV,
Shielded-Tape, Wire, UniShield, LC Cold Shrink Splices}

^{1/C, 5 - 15
kV, Shielded-Tape, Wire, UniShield Tape Splices}

^{3/C, 15 kV,
Shielded Armored or Non-Armored Cold Shrink Splices}

^{25/28 kV Splices}

^{1/C, 25/28
kV, JCN/CN Molded Rubber Splices}

^{1/C, 25/28
kV, JCN/CN Cold Shrink Splices}

^{1/C, 25/28
kV, Shielded-Tape, Wire, UniShield, LC Cold Shrink Splices}

^{3/C, 25/28 kV
Shielded Armored or Non-Armored Cold Shrink Splices}

^{35 kV Splices}

^{1/C, 35 kV,
JCN/CN Molded Rubber Splices}

^{1/C, 35 kV,
JCN/CN Cold Shrink Splices}

^{1/C, 35 kV,
Shielded-Tape, Wire, UniShield, LC Cold Shrink Splices}

^{3/C, 35 kV,
Shielded Armored or Non-Armored Cold Shrink Splices}

^{PILC Splices
and Accessories}

^{1/C Low
Voltage Splices 0-600V (1000V rated)}

^{1/C to 1/C,
15 kV Cold Shrink Splices}

^{3/C to 1/C,
15 kV Cold Shrink Splices}

^{3/C to 3/C,
15 kV Cold Shrink Splices}

^{5740系列預張式直路接頭適用於5－8KV之無遮蔽型電纜之直路接續用
使用此接頭做電纜的直路接續不需要特別的工具，噴燈或特殊之技巧便能讓您得到一兼具良好防水性及絕緣性的接頭
每一組5740接頭包括三只預張式矽橡膠套管、三卷#2228自融性防水膠帶、三包清潔拭紙及施工說明書（壓接套管請自行選購）。此組件足夠讓您完成三條電纜的直路接續}

^{5550系列預張式橡膠接頭適用於5KV遮蔽，塑膠絕緣（Solid Dielectric）之電力電纜使用在銅或鋁導線之線徑範圍從6AWG到1000Kcmil

16-500mm2）此接頭使用3M10,000，11,000及20,000系列之壓縮套管（inline compression
connectors）或任何符合您線徑需要的UL註冊之壓縮套管}

^{5730系列預張式直路接頭適用於600V及1KV之三芯無遮蔽鎧裝電纜之直路接續用
使用此接頭做電纜的直路接續不需要特別的工具，噴燈或特殊之技巧便能讓您得到一兼具良好防水性及絕緣性的接頭並能恢復裝甲電纜原有之機械強度}

^{4560鎧裝(裝甲)電纜修護包紮帶 (4560 Armorcast Material) 電纜修護包紮帶是一種鋼性非常強的電纜外被修復補強的材料
攜帶型的小包裝最適合現場施工使用施工非常簡便不須要特別工具或火烤，只需要加入適量的水包紮完成後，自然硬化(約20分鐘)即可
完成後將恢復電纜原本之鋼性結構固化時間快速可節省相當多的施工時間
包紮帶固化後兼具有良好的防水及氣密性，是氣體或液體管路之修補的最佳材料}

您可能會需要:

Tubular Cable Lug 加長型 (高壓) 單孔銅管端子/加長型 (高壓) 雙孔銅管端子

For other QT-II termination 其他 3M QT-II電纜處理頭

^{3M Cable
Cleaning System 電纜清潔劑}

^{外半導體剝除工具}

中央商業有限公司 Power Hub Inc.