^{3M Scotchcast Flexible Power Cable Splicing Kits 82-F1  82-F2 82-BF 電力絕緣防水中間接頭}

3M Scotchcast 82-F and 82-BF Series Flexible Power Cable Splicing Kits are a series of flexible inline and tap splices for use on non-shielded portable power cables and cords. They are designed to be used on single and multiple conductor cables and cords rated up to 1000 Volts (600/2000 Volts mine portable cable rating). The 82-F Series will accommodate a single-conductor cable rated up to 5 kV. The splices will accommodate single-conductor cables sized up to 4/0 for inline splicing and up to 1/0 for tap splicing. Multi-conductor sizing is based on a cable diameter range of up to 1.2 inches for inline splicing and up to 0.8 inches for tap splicing.

The splice kits are based on Scotchcast 2130 Compound for toughness, flexibility, moisture sealing and flame retardancy. They are permanent splices as assigned by the Mine Safety and Health Administration (P-l42-5 MSHA). The completed splices are designed for use in weather exposed, direct burial or submerged locations.
 

Kit Contents:
Each kit contains sufficient quantities of the following materials to make one splice or cable repair (connectors are not included in kit):
- One-piece removable mold
- Scotchcast 2130 Compound in "Unipak" container
- Scotch 23 Tape, for sealing mold ends
- Abrasive cloth (80J grit)
- Comprehensive instructions showing proper installation techniques for splicing non-shielded portable power
cables and cords.

Applications:

To join or re-jacket non-Armoured portable power cable and portable cords

For inline single-conductor cables rated up to 5kV

For branch single-conductor cables rated up to 1000V

For inline and branch multi-conductor cables rated up to 1000V

For mine portable cable rated 600/2000V (P-145-5 MSHA)

For use with compression inline connectors (82-F) and compression “C” branch connectors (82-BF)

For jacket repairs

For indoor and outdoor applications: Weather exposed /Direct burial /Submerged / Cable reels

Each kit contains sufficient quantities to make one splice or cable repair (connectors are available separately)

^{3M Scotchcast resin joint kits 92-NBA x 灌膠式防水中間接頭 Resin Kit 92-NBA 0 up to 92-NBA 7 Inline Joint Kit Series with Resin 40}

3M  Scotchcast  resin joint kits 92-NBA x are designed to be used for 1-core up to 5-core non shielded, polymeric, low voltage energy cables up to 0.6/1 (1.2) kV. 3M  Scotchcast  resin inline joint kits contain a one-part transparent mould body for simple and easy handling and so distances inside the body can be checked easily. Also included is 3M  Scotchcast  40 Polyurethane resin, delivered in a two-chamber bag with an integrated spout and aluminium guard bag for protection against humidity.

適用電纜外徑 min-max    Cable outside diameter (mm)

* Resin 40 comes in two transparent chamber bags with an integrated Closed Mixing and Pouring (CMP) system.
* One-part mould body with a snap fit closing system for quick and easy handling.
* Transparent mould body for easy control of connector distances in the joint.
* Web spacer for 4-core cable application to ensure the distance between connectors for sizes NBA 1 up to NBA 4.
* Pre-cut foam sealing elements to provide reliable sealing to the mould body without tooling for all cable application diameters.
* Abrasive sponge to clean and roughen the cable jacket.
* Closure cap to prevent any pollution.
 

Type of Test according to EN50393 Table 3 / I / A1        Results
AC Voltage Withstand Test in air 4kV AC/ 1 min           passed
Insulation Resistance Test in air 1kV DC                      > 10.000MΩ
Heat Cycle in air 63 cycles: 5h/3h                               passed
Heat Cycle in water 63 cycles: 5h/3h                           passed
AC Voltage Withstand Test in water 4kV AC/ 1 min      passed
Insulation Resistance Test in water 1kV DC                 > 10.000MΩ